mold removal: getting rid of mold behind your cabinets - bathroom vanity units

by:KEDIBO     2019-09-14
mold removal: getting rid of mold behind your cabinets  -  bathroom vanity units
googletag. display("div-ad-articleLeader");
There are things that often happen that often cause mildew behind the bathroom or kitchen cabinets.
The first one is water leakage.
There is a sink in each location, and a leaking dishwasher is often found in the kitchen.
In addition to the possibility of water leakage, these rooms tend to be high-moisture rooms, sometimes allowing mold to grow behind the cabinets, especially in homes where modern mold prevention supplies are not updated.
The good news is that if the mold does grow behind your cabinet, what can you do about it, you can throw it away.
Contains the area.
It is important that you use plastic to control the area so that mold spores do not spread throughout the house.
To do this, attach the plastic film to the ceiling and floor using adhesive tape, covering all open areas, including doors and some walls.
You'll want to make a doorway by overlapping two layers of plastic without attaching the lower half of this part.
You should also put a fan on the window and let it blow the air out so that it helps to reduce the pressure and also to drain the mold spores instead of leaving them inside.
For more information, see mold removal: containment area. Safety Gear.
More and more people have recently learned about the dangers of toxic mold and how it can make you sick.
It is important that you wear long rubber gloves, safety goggles and respirator designed to protect you from mold spores.
Please see this article for more information about protecting yourself and the people who help you.
Remove the cabinet.
It's not easy to pull cabinets (
Or vanity in the bathroom)
, But this can be done by some work.
Here are some basic instructions.
Unplug the appliance and water.
Make sure you don't forget the top series of garbage disposal and cooking (
If you have these things).
Next, it will be used to seal the sink in place and cut off the caulking or grouting at the top of the counter.
Both items must be deleted and put on hold.
It should be easy once the seal breaks.
Next you need to remove all the doors and hinges and you need to remove the drawer.
At this point, you should unscrew the cabinets from each other.
Make sure you get all the screws!
Screw them off the wall.
Carefully separate them from each other.
If they are stuck together, use something to force them to separate a bit.
Clean the mold on the back of the cabinet.
In an ideal world, people will take advantage of this opportunity to change cabinets, preferably with something better.
If this is in the budget, or if the insurance company is paying for it, buy it.
This can save a lot of work.
To get rid of moldy cabinets, you should wrap them in plastic wrap and then close them with tape (
Learn more about how to handle Moldy items).
If it's not a perfect world for you, you need to save some money, you can clean up the moldy cabinets, but it will bring more work.
Spray them to the entire back of the cabinet with hydrogen peroxide.
Hydrogen peroxide is safe for people and pets, but it kills mold.
Put it there for about ten minutes.
Come back with a sponge and fresh water and put a little soap in it to remove the mold.
Repeat until the mold is gone.
Now spray it with hydrogen peroxide and dry it.
Next, you should clean all the sides and even the interior in a similar way.
Done by drawing the back and sides (
Will not be seen)
Primer with mold blocking.
Make sure you can also get the inside surface with mildew proof primer.
Following these instructions will kill the mold as much as possible and seal it so that it will not be exposed to moisture in the future.
Mold on the back wall.
Next, you will want to clean the mold on the back wall behind the cabinet.
To do this, you follow the same method as cleaning the cabinets, but this time on the wall panel.
It is important that you repeat the process and kill the mold as much as possible.
You will then want to paint it with a mildew proof primer and some mildew proof paint.
For more information on removing the mold in the wall panel, check the mold removal: process the wall panel.
Put everything together again.
You want to make sure you have enough time to dry the paint and primer.
Then you should screw the cabinet to the other side like you take apart the cabinet.
Screw them to the wall, connect the countertop to the sink with good sealing material, and then plug everything/hook. Clean It.
The last thing you need to do before you call it a day is clean everything.
Wash all surfaces in water using vinegar, hydrogen peroxide or soap.
Remove the plastic and place it in a black garbage bag.
Seal the bag with duck tape.
Put that bag in the second bag and put that bag in the tape as well.
Then throw away the mold.
Making sure everything is cleaned will reduce the number of mold spores, which is important because it means less chance of getting moldy again. Prevent Mold.
It is also important to prevent mildew.
You will want to do this by lowering the overall humidity of the house.
It is particularly important to do so in the kitchen, bathroom and laundry room.
For more information on how to do this, please visit how to prevent mold at home.
Mold is never fun, but due to its ability to get out of control and the frequency of health problems it is important to deal with them quickly when they arise.
You can clean the mold from behind the cabinet!
Function articleAdMiddleLoad (){if (typeof jQuery ! = "undefined"){
Last position of Var = 0;
Minimum distance between Ads var = 1200;
Minimum distance from var at the bottom = 300;
Var adsToPlace = 20; for(var i = 1;
I /element is located after the ad & in the last position! $(this). hasClass(
"Article ")
/Element is not advertising &&($(this). position(). top -
Enough space between Ads & $ (". articleText"). height()-$(this). position().
Enough space from the bottom of the article | $ (this). prev(). hasClass(
"Article ")
/The previous element is a slide)){$(this). before($(
"ArticleAdMiddle ")); googletag. display("div-ad-
"I ");
$ (this). position(). top;
SpotFound = true; return false; }});
/If no location is found, stop looping and remove any remaining banner slots. if(! spotFound){for(var j = i;
J
Custom message
暂无友情链接数据
Chat Online 编辑模式下无法使用
Chat Online inputting...